And maybe even wirelessly, because Bluetooth can also connect the CoreStation. ▶ The CoreStation is your control centre: whether it’s a Blu-ray player, game console, TV or system – they all find their connection, whether analogue or digital. This is usually the best way to connect your computer to the amplifier. Even if you have installed a high-quality sound card in your computer, you will usually find a TOSLINK or coaxial output there. Game consoles can also transmit their 5.1 signal to the amplifier via these digital inputs. This is usually connected via HDMI, but it is also possible to connect via a TOSLINK cable. This input is therefore not suitable for use with an mp3 player or another analogue playback device but can work with all digital players such as a Blu-ray player. Of course, no analogue devices can be connected to digital audio inputs, only those with a digital output. In this case, there is one input for one coaxial cable and two TOSLINKinputs: Rearview of the CoreStation But there are also – especially with modern amplifiers like the CoreStation (shown above) – digital audio inputs. Most of the audio inputs, and all those that we have covered in this text so far, are analogue connectors. Teufel CoreStation – 5.1 AV receiver: The centre of your home theatre with which all other components (must) connect Digital connections That way you can quickly switch to the corresponding channel later and have the device that is located at the corresponding input already selected. The different designations primarily serve the order of the individual devices. But don’t worry: All these connections are basically AUX inputs, except for the previously mentioned phono input. The amplifier may have audio inputs titled line-in, CD or Tuner. Some manufacturers contribute to the confusion by using many different names for the audio inputs of their devices. Should neither amplifier nor record player has an integrated pre-amplifier, you have to reach for a phono amplifier – you can read more about this type of pre-amplifier here. When it is installed in the amplifier, in addition to the AUX input, there is also a so-called phono input, via which record players without integrated pre-amplifiers should be connected. If the pre-amplifier is in the record player, the AUX input of the amplifier can be used without any problems. This can either be integrated into the record player itself or be part of the amplifier. Often the device signal is too weak so that users of modern amplifiers can only hear a few quiet noises – if at all. In theory, they can also be connected to the amplifier without special cables, but whether they will actually work is another question. AUX cable, also available at TeufelĬonnecting a record player to sound system – what cable to use?Ĭonnecting record players is usually more complicated. To connect your iPod to it, you need a simple 3.5 mm jack to stereo RCA cable. The most common are RCA connectors – one red and one either white or black for the two stereo channels. It merely describes the purpose of this connection, not whether it is a jack or RCA connection. However, the term AUX does not clarify exactly which cable to use. If you want to quickly and easily connect your computer, it’s also best to use the AUX input.Īs a rule of thumb, devices to which you can connect headphones can normally also be connected to your system via an AUX cable. This could be anything from an old cassette deck or a modern player such as an mp3 player or smartphone. This is simply an audio input to which you can connect players of your choice. RCA input sensitivity 0.316 ÷ 3.Alongside the inputs for various players such as Blu-ray players and connections for the speakers themselves, the most important input on the amplifier or compact system is called AUX or auxiliary.Rear potentiometer to adjust antenna reception sensitivity. Rear connectors for stereo audio input (2 RCA pairs) and for audio programs + intercom bus (20 way ribbon wire socket). The 1202 controller module will allow to switch between the FM tuner or an external audio source in order to assign the corresponding audio program. This input will not provide the installation with an additional audio program. Pair of rear RCA stereo connectors for input of external music source.Ī low level input through a RCA connector is available. Modular FM digital tuner as an internal music source in the sound installation.įront LED to indicate the line output activation, front LED to indicate the operation of the FM tuner, front LED to indicate the RCA input status and front LED to indicate the ON/OFF status.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |